給袋式包裝機的整個結構體系和各機構的功能體現在整個包裝作業過程中。預制袋放置在儲袋裝置處。通過主傳動軸的運動，運動和動力通過儲袋裝置的升降機構沿導桿軌跡傳遞給儲袋裝置，實現儲袋裝置的升降動作。當儲袋裝置上升到極位時，裝置上部的吸盤（以真空泵為動力源）吸收預制袋，使取袋機械手可以取袋。主傳動軸帶動聯動凸輪轉動，聯動凸輪帶動取袋機械手的大臂和小臂協調配合。

預制好的行李通過一定的軌道送到第  一站的夾袋裝置，然后連續通過第二站的編碼裝置（選配）送到第三站；第三工位的操作順序為：先將夾鉗的寬度變窄，上下開袋裝置打開袋子，再由吹氣裝置吹氣，使袋口限度打開，然后由托袋機械手支撐袋子，開袋裝置的吸盤停止吸附，機械手保持此狀態至第四工位；在第四站，依次進行充、出料振動操作，托袋機械手后退。然后，當六工位轉臺裝置轉到第五工位熱封裝置時，夾鉗變寬。

當到達第五工位時，夾鉗達到最寬，袋口閉合，便于熱封。如果袋內氣體量過大，多余的氣體可通過排氣裝置排出，重新加熱密封；利用第六位成型裝置對包裝袋進行成型放置，完成包裝作業。六位機構由六位凸輪驅動基準主軸驅動，基準主軸的運動和動力由主傳動軸通過傘齒輪組傳遞。物料輸送系統負責將物料輸送至電子秤裝置。